CFD Analysis of the Slippage Effects on Elastohydrodynamic Lubrication in Line Contact Problem

Main Article Content

Sutthinan Srirattayawong

Abstract

In this paper, the effects of a slippage on an elastohydrodynamic lubrication (EHL) in line contact problem using an advanced computational fluid dynamics (CFD) model are presented. A cylindrical roller is assumed to be infinitely long and rotates on a plate under an applied load. In addition, the no-slip and slip boundary conditions were defined between lubricant and solid walls. The Navier-Stokes and the elasticity equations were solved simultaneously. The Ree-Eyring model was used to calculate the viscosity of lubricant. The developed CFD model had been applied to the series of cases of lubricated slippage effect with the applied loads L=1.5 kN and 2.5 kN, slide-to-roll ratios: SRR =0, 1 and 2 under the thermal condition. The flow characteristics in the CFD model such as the pressure distribution, the fluid film thickness, the velocity of fluid flow, the viscosity and the temperature distribution were investigated. To illustrate, the developed CFD model is successively to simulate the EHL line contact problem, and can deal with the slippage problem. The simulation results show that the slippage effect is significant to the EHL problem, especially in the case of pure sliding.

Article Details

How to Cite
Srirattayawong, S. (2018). CFD Analysis of the Slippage Effects on Elastohydrodynamic Lubrication in Line Contact Problem. Naresuan University Engineering Journal, 13(2), 19–25. Retrieved from https://ph01.tci-thaijo.org/index.php/nuej/article/view/101799
Section
Research Paper

References

O. Reynolds, (1886), "On the theory of lubrication and its application to Mr. Beauchamp Tower's experiments, including an experimental determination of the viscosity of olive oil", Philosophical Transactions of the Royal Society of London, vol. 177, pp. 157-234.

H. Martin, (1916), "Lubrication of gear teeth," Engineering, London, vol. 102.

L. , (1916), " (On the Lubrication of Gears)" , Zeitschrift fur das Gesamte Turbinenwesen, vol. 13.

A. Meldahl, (1914), "Contribution to the Theory of the Lubrication of Gears and of the Stressing of the Lubricated Flanks of Gear Teeth", Brown Boveri Review, vol. 28, pp. 374-382.

A. von Mohrenstein-Ertel, (1949), "Die Berechnung der Hydrodynamischen Schmierung unter Hoher Belastung und Relativbewegung", Fortschrittsberichte VDI, vol. Ser. 1, No. 115.

A. I. Petrusevich, (1951), "Fundamental conclusions from the contact-hydrodynamic theory of lubrication", Izv. Akad. Nauk. SSSR (OTN), vol. 2, p. 14.

D. Dowson and G. R. Higginson, (1959), "A numerical solution to the elasto-hydrodynamic problem", Journal of Mechanical Engineering Science, vol. 1, pp. 6-15.

M. E. Muller, (1958), "An inverse method for the generation of random normal deviates on large-scale computers", Mathematics of Computation, vol. 12, pp. 167-174.

H. S. Cheng and B. Sternlicht, (1965), "A Numerical Solution for the Pressure, Temperature, and Film Thickness Between Two Infinitely Long, Lubricated Rolling and Sliding Cylinders, Under Heavy Loads", Journal of Basic Engineering.

C. H. Venner, (1991), "Multilevel Solution of the EHL Line and Point Contact Problems", PhD, University of Twente, Enschede, Netherlands.

A. A. Lubrecht, (1987), "Numerical solution of the EHL line and point contact problem using multigrid techniques", Ph.D. Thesis, University of Twente, Endschende, Netherlands.

H. Okamura, (1983), "A contribution to the numerical analysis of isothermal elastohydrodynamic lubrication", Proc. 9th Leeds-Lyon Symp. on Tribology, pp. 313-320.

D. Dowson, (1962), "A generalized Reynolds equation for fluid-film lubrication", International Journal of Mechanical Sciences, vol. 4, pp. 159-170.

D. Dowson, G. Higginson, and A. Whitaker, (1962), "Elasto-hydrodynamic lubrication: a survey of isothermal solutions", Journal of Mechanical Engineering Science, vol. 4, pp. 121-126.

L. Houpert, (1985) "New results of traction force calculations in ehd contacts", Trans. ASME, J. Lub. Tech., vol. 107, p. 8.

C. J. A. Roelands, (1966), "Correlational Aspect of Viscosity-Temperature-Pressure Relationships of Lubricating Oils", PhD Thesis, Delft University of Technology, Netherlands.

B. Sternlicht, P. Lewis, and P. Flynn, (1961), "Theory of lubrication and failure of rolling contacts", Journal of Basic Engineering, vol. 83, p. 213.

P. C. Sui and F. Sadeghi, (1990), "Thermal Elastohydrodynamic Lubrication of Rolling/Sliding Contacts", Trans. ASME, Jour. Trib., vol. 112, p. 6.

K. L. Johnson and J. L. Tevaarwerk, (1977), "The shear behaviour of elastohydrodynamic oil films", Proc. R. Soc. London, vol. A. 356, pp. 215-236.

Y. Peiran and W. Shizhu, (1990), "A generalized Reynolds equation for non-Newtonian thermal elastohydrodynamic lubrication", Journal of tribology, vol. 112, pp. 631-636.

S. H. Wang, D. Y. Hua, and H. H. Zhang, (1988), "Full numerical EHL solution for line contacts under pure rolling condition with a non-Newtonian rheological model", Journal of Tribology, vol.110, pp. 583-586.

S. P. C. and F. Sadeghi, (1991), "Non-Newtonian Thermal Elastohydrodynamic Lubrication", Trans. ASME, Jour. Trib., vol. 113, p. 6.

S. Bair, J. a. Jarzynski, and W. O. Winer, (2001), "The temperature, pressure and time dependence of lubricant viscosity", Tribology International, vol. 34, pp. 461-486.

K. F. Osborn and F. Sadeghi, (1992), "Time Dependent Line EHD Lubrication Using the Multigrid/Multilevel Technique," ASME. Journal of Tribology, vol. 114, pp. 68-74.

X. Ai and H. S. Cheng, (1994), "A Transient EHL Analysis for Line Contacts With Measured Surface Roughness Using Multigrid Technique", Journal of Tribology, vol. 116, pp. 549-556.

A. Almqvist, (2004), "Rough Surface Elastohydrodynamic lubrication and Contact Mechanics", PhD, Department of Applied Physics and Mechanical Engineering, Lulea University of Technology.

D. Zhu and Y. Hu, (2001), "Effects of Rough Surface Topography and Orientation on the Characteristics of EHD and Mixed Lubrication in Both Circular and Elliptical Contacts", Tribology Transactions, vol. 4, p. 7.

N. Patir and H. S. Cheng, (1978), "An Average Flow Model for Determining Effects of Three-Dimensional Roughness on Partial Hydrodynamic Lubrication", ASME Journal of Lubrication Technology, vol. 100, pp. 12-17.

C. H. Venner and W. E. Ten Napel, (1992), "Surface Roughness Effects in an EHL Line Contact", ASME Journal of Tribology, vol. 114, pp. 616-622.

T. Almqvist and R. Larsson, (2002), "The Navier-Stokes approach for thermal EHL line contact solutions", Tribology International, vol. 35, pp. 163-170.

T. Almqvist, A. Almqvist, and R. Larsson, (2004), "A comparison between computational fluid dynamic and Reynolds approaches for simulating transient EHL line contacts", Tribology International, vol. 37, pp. 61-69.

M. Hartinger, D. Gosman, S. Ioannides, and H. Spikes, (2005), "CFD modelling of elastohydrodynamic lubrication", Washington, D.C., pp. 531-532.

M. Hartinger, M. L. Dumont, S. Ioannides, D. Gosman, and H. Spikes, (2008), "CFD modeling of a thermal and shear-thinning elastohydrodynamic line contact", Journal of Tribology, vol. 130, pp. 179-180.

V. Bruyere, N. Fillot, G. E. Morales-Espejel, and P. Vergne, (2012), "Computational fluid dynamics and full elasticity model for sliding line thermal elastohydrodynamic contacts", Tribology International, vol. 46, pp. 3-13.

S. Srirattayawong and S. Gao, (2012), "A CFD Study of the EHL Line Contact Problem with Consideration of the Surface Roughness under Varied Loads", presented at the 9th International Conference on Heat Transfer, Fluid Mechanics and Thermodynamics, Malta.

H. Hertz, (1881), "The contact of solid elastic bodies [Über die Berührung fester elastischer Körper]", Journal für die reine und angewandte Mathematik, vol. 92, pp. 156-171.

K. L. Johnson, (1985), Contact mechanics, Cambridge: Cambridge University Press.

Y. H. Wijnant, (2005), "Contact Dynamics in the Field of Elastohydrodynamic Lubrication", Ph.D. Thesis, , University of Twente, The Netherlands.

G. Gasni, M. K. Wan Ibrahim, and R. S. Dwyer-Joyce, (2011), "Measurements of lubricant film thickness in the iso-viscous elastohydrodynamic regime", Tribology International, vol. 44, p. 11.

L.-M. Chu, H.-C. Hsu, J.-R. Lin, and Y.-P. Chang, (2009), "Inverse approach for calculating temperature in EHL of line contacts", TribologyInternational, vol. 42, pp. 1154-1162.

S. Srirattayawong and S. Gao, (2013) "A computational fluid dynamics study of elastohydrodynamic lubrication line contact problem with consideration of surface roughness", Computational Thermal Sciences, vol. 5, pp. 195-213.